Emtron 8 button CAN keypad providing programmable switching for all Emtron ECUs. Each button independently supports multiple operating modes — from simple toggle to 8-position binary — enabling precise control over engine, display, and vehicle functions directly from the cockpit. Three RGB LED indicators above each button show current state at a glance. Configured entirely via Emtune software.
The keypad ships blank. The included sticker sheet is applied after programming to label each button for the driver.
Button Modes
Each of the 8 buttons is independently configurable:
| Mode |
Type |
Positions |
| 0 |
Toggle |
OFF / ON |
| 1 |
Sequential |
OFF, Position 1, Position 2 |
| 2 |
Sequential |
OFF, Position 1, Position 2, Position 3 |
| 3 |
Binary |
8 distinct states |
| 4 |
Momentary |
Active while pressed |
LED Indicator Behaviour
| Mode |
LED Sequence |
| Toggle |
Off → Green |
| 3-Position |
Off → Green → Amber |
| 4-Position |
Off → Green → Amber → Red |
| 8-Position Binary |
All combinations of Red, Amber, Green |
| Momentary |
Green while pressed |
Connector Pinout — Deutsch DT4
| Pin |
Function |
Wire Colour |
| 1 |
12V Supply |
Red |
| 2 |
Ground |
Black |
| 3 |
CAN Hi |
Yellow |
| 4 |
CAN Lo |
Green |
CAN Bus Wiring Notes
- No on-board termination resistor — can be placed at any point on the bus
- 120Ω (0.25W) resistor required at each end of the CAN bus
- CAN Hi/Lo must be wired with twisted pair cable
- Maximum stub length from main bus: 0.3m (ISO 11898)
Technical Specifications
| Parameter |
Value |
| Power |
|
| Supply Voltage |
8–22V |
| Current Limit |
0.2A |
| Protection |
Reverse battery, short circuit |
| Communications |
|
| CAN Bus |
Single CAN, 1 Mbps baud rate |
| Emtune Dataset |
40 — Emtron 8-way Keypad |
| Firmware Required |
v2.15.0 or later |
| Physical |
|
| Dimensions |
104.7mm × 62.82mm × 21.72mm |
| Mounting |
M6 × 1.0mm studs (2 places) |
| Connector |
Deutsch DT4 |
| Environmental |
|
| Operating Temperature |
-40°C to +85°C |
| LEDs |
|
| Red |
640nm |
| Amber |
601nm |
| Green |
525nm |
Emtune Configuration
Access keypad programming via: Config → Communications → Emtron CAN Devices → Emtron Keypad
Configure per button: mode, memory function, backlight brightness, LED brightness. Changes take effect after cycling keypad power.
Backorder Products
These items aren't kept in stock but are available for purchase.
Sensor connectors and Deutsch DT/DTM/DTP connector kits sometimes are listed as Backorder items, but we stock seperate items, so it only takes to collect these for your shipment in kits.
These items are supplied on backorder. Delivery times depend on each manufacturer's production schedule and current demand, so the figures below are typical estimates under normal conditions — not guaranteed delivery dates. When demand is high, lead times can extend beyond the ranges shown.
For made-to-order items or products requiring special configuration, production begins only after your order is placed and paid. The binding delivery date is the one the manufacturer confirms once your order is scheduled; we pass it on as soon as we receive it and keep you updated on any change.
Typical lead times (normal demand):
- Bosch Motorsport ABS: 3–4 weeks
- Emtron: ~4 days
- AiM: 2–7 days
- Ecumaster: 1–2 days
- Link: up to 1 week
Please check the estimated delivery time on each product page, and get in touch if you need a current estimate before ordering.
Orders Processed by 14:00 GMT+3 (EET )Monday-Friday Ship The SAME DAY!
In-stock items only, excluding holidays.
Items that are in stock will be shipped within 24 to 48 hours. However, if you place your order before 14:00 GMT+3 (EET) and the items are available, they will usually be dispatched on the same day. If any items need to be drop-shipped from a supplier, we will ensure they are sent out as quickly as possible. If you have any questions or need special shipping arrangements, please feel free to contact us.
- We offer shipping via UPS and DHL. Economy or Express services.
- We ship to Europe and internationally from our stock.
- Remote location fee. Additional fee for non-standard remote destination location surcharge is 20 Eur per shipment. We will contact you in case of remote location.
- Confirmation e-mails are sent immediately after your package is shipped, complete with estimated delivery date and tracking information (trackable shipping methods only).
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.